Pulse Width Modulation (PWM)#

Todo

Add further testing steps, results, and images..

What is it#

PWM or Pulse Width Modulation, is a technique used to control the amount of power delivered to an electronic device by breaking up the power signal into discrete ON and OFF periods. The amount of time the signal spends ON during each cycle determines the output power level (brightness of the LED).

../../../../_images/pwm.jpg

Configuring PWM overlay#

To enable any of the PWM Pins, we have to modify the following file: /boot/firmware/extlinux/extlinux.conf. We can check the available list of Device Tree Overlays using command below,

ls /boot/firmware/overlays/ | grep "beagley-ai-pwm"

When executed the above command should give output show below,

debian@BeagleBone:~$ ls /boot/firmware/overlays/ | grep "beagley-ai-pwm"
k3-am67a-beagley-ai-pwm-ecap0-gpio12.dtbo
k3-am67a-beagley-ai-pwm-ecap1-gpio16.dtbo
k3-am67a-beagley-ai-pwm-ecap1-gpio21.dtbo
k3-am67a-beagley-ai-pwm-ecap2-gpio17.dtbo
k3-am67a-beagley-ai-pwm-ecap2-gpio18.dtbo
k3-am67a-beagley-ai-pwm-epwm0-gpio12.dtbo
k3-am67a-beagley-ai-pwm-epwm0-gpio14.dtbo
k3-am67a-beagley-ai-pwm-epwm0-gpio15.dtbo
k3-am67a-beagley-ai-pwm-epwm0-gpio5.dtbo
k3-am67a-beagley-ai-pwm-epwm1-gpio13.dtbo
k3-am67a-beagley-ai-pwm-epwm1-gpio20.dtbo
k3-am67a-beagley-ai-pwm-epwm1-gpio21.dtbo
k3-am67a-beagley-ai-pwm-epwm1-gpio6.dtbo

Using hat-08 (GPIO14) as pwm#

Add the line shown below to /boot/firmware/extlinux/extlinux.conf file to load the gpio14 pwm device tree overlay:

fdtoverlays /overlays/k3-am67a-beagley-ai-pwm-epwm0-gpio14.dtbo

Your /boot/firmware/extlinux/extlinux.conf file should look something like this:

label microSD (default)
   kernel /Image
   append console=ttyS2,115200n8 root=/dev/mmcblk1p3 ro rootfstype=ext4 resume=/dev/mmcblk1p2 rootwait net.ifnames=0 quiet
   fdtdir /
   fdt /ti/k3-am67a-beagley-ai.dtb
   fdtoverlays /overlays/k3-am67a-beagley-ai-pwm-epwm0-gpio14.dtbo
   initrd /initrd.img

Now reboot you BeagleY-AI to load the overlay,

sudo reboot

How do we do it#

To configure HAT pin8 (GPIO14) PWM symlink pin using beagle-pwm-export execute the command below,

sudo beagle-pwm-export --pin hat-08

Let’s create a script called fade.sh that cycles through LED brightness on HAT pin8 by changing PWM duty cycle.

touch fade.sh

Now open the file with nano editor,

nano fade.sh

In the editor copy paste the script content below,

#!/bin/bash

PWMPIN="/dev/hat/pwm/GPIO14"


echo 1000 > $PWMPIN/period
echo 0 > $PWMPIN/duty_cycle
echo 0 > $PWMPIN/enable
sleep 1

for i in {1..500};
do
        echo $i > $PWMPIN/duty_cycle
        echo 1 > $PWMPIN/enable
        echo $i
        sleep 0.0005
done

for i in {500..1};
do
    echo $i > $PWMPIN/duty_cycle
    echo 1 > $PWMPIN/enable
    echo $i
    sleep 0.0005
done
  • Close the editor by pressing Ctrl + O followed by Enter to save the file and then press to Ctrl + X exit

  • Now execute the fade.sh script by typing:

bash fade.sh
LED PWM fade demo

Fig. 136 LED PWM fade demo#

  • You can exit the fade.sh program by pressing Ctrl + C on your keyboard.

Todo

Add section about driving Servo Motors at 50KHz

Troubleshooting#

Todo

Fill out empty section

Going Further#

Todo

Fill out empty section